Climb Milling vs. Conventional Milling

Sep 21, 2015 | Blog

As a machinist you hear lots of technical terms getting thrown around. The old guys call it one thing and the young guys call it another. If you are not a machinist or are just entering the world of machining this can be confusing. Today I am going to discuss two of these confusing terms – climb milling and conventional milling.  Knowing the difference between the two and the proper application can set you apart from your peers and bring your overall part quality to the next level.

First things first, let’s set some ground rules. We will be running our spindle forward (clockwise) and using a standard end mill – we’ll get into down-cutting end mills and many other tooling options in a later blog post. For now, we are going with standard tools and we will go through the benefits and drawbacks on both manual and CNC machines.

With the tool rotating clockwise climb milling goes WITH the rotation. Think of the flutes, or teeth of the cutter as pulling the material, or CLIMBING through the material. When climb milling the flute hits the material at the top of the cut, and the thickness of the chip decreases as the flute cuts. This results in the chips being deposited BEHIND the cut, which is important. The chips clear the cutter, which means you are not re-cutting chips. Since you are not re-cutting chips, the result is a better surface finish and longer tool life. Less power is required from the spindle to climb mill, and the result of the cut is down-force on the material, which can simplify workholding considerations. Also when finishing the floor of a feature or face milling thin material the down force can assist in stabilizing the part.

Climb milling vs. conventional milling is determined based on the machining application and the advantages and disadvantages of both milling strategies.

Climb Milling – chips are evacuated behind the cut, so that you are not re-cutting them which results in a better surface finish.

There are however downsides to climb milling, the most severe of which will be found on manual machines. When performing a climb mill on a 60 year old Bridgeport you can run into some serious issues with backlash. Due to the pulling action of the tool on the material if you are using a machine that has a good amount of backlash the tool will grab the material and the table will move whatever distance that backlash is – on some machines this could be not only disastrous to the part, but incredibly dangerous to the machinist. Tool deflection (which we will cover in another post) with a climb mill will be perpendicular to the tool – so away from and into your part which will affect the thickness of your chip and potentially compromise your accuracy.

With the tool rotating clockwise conventional milling goes AGAINST the rotation. The flutes of your cutter are hitting the material and pushing against the rotation, depositing chips IN FRONT of the cut.  As expected, that will result in re-cutting of the chips which will both increase tool wear and decrease surface quality. Since the tool hits at the bottom of the part and the flute cuts upward with the chip getting heavier as it cuts, you are creating upward force on the part which can cause workholding issues.

Conventional milling vs. climb milling is the topic of this blog and advantages and disadvantages of both are discussed.

Conventional Milling – offers a significant benefit when machining hard materials like cast iron or hot rolled steel.

Just as there are downsides to climb milling there are upsides to conventional milling. When machining things like rough cast iron, or hot rolled steel, conventional milling is the preferred method. Especially with hot rolled steel due to the hard black layer on the outer surface. Performing a climb mill on hot rolled steel can result in chipped cutting edges because of the hardness of that outer layer and the more aggressive way the tool engages the rough surface, causing more deflection and potentially heavier chips. Since the tool deflection with a conventional mill tends to be parallel to the tool, it engages the rough surface at a more forgiving rate. Another strong suit of conventional milling is on finish passes. If you rough your profile with a climb mill, which will give you a good surface finish to begin with and then switch it up on the finish with a light conventional mill you will be surprised by the results. Due to the tool deflection seen with climb milling the conventional mill finish pass will give you a good finish on a light pass. Another option is a “ghost pass” or “spring pass” which is a cut in the opposite direction, in this case conventional, without actually taking a heavier cut. You will see the amount of material being removed, which was left by the tool deflection and it will leave a great finish as long as you lubricate.

Hopefully I clarified the issue of climb milling vs. conventional milling for you at least a little bit.  Both are useful strategies when applied in the proper situation. Always remember, when it comes to machining it’s the small details that make all the difference – no matter how small they may seem.


High-Speed CNC machining is more than 60,000 RPM spindle-speed. When you’re making small or complex parts, you need speed and precision at every stage. DATRON AG engineers didn’t just invent a faster, more precise CNC machine. They re-interpreted and optimized your entire machining workflow from start to finish.

About the Author

Kevin Mulhern is an Applications Engineer at DATRON Dynamics. He has over a decade of experience in the industry starting as an apprentice learning the old school ways of manual machining, as well as nearly ten years as a CNC Programmer/Machinist. This industry experience affords him the knowledge to understand the challenges facing our customers on a daily basis.

DATRON Archives

Discover How You Can Revolutionize Your Entire Workflow Today

DATRON machines dramatically reduce practically every aspect of your machining workflow. Download our FREE Workflow Optimization Map and learn how today.

Share This
Shopping Cart
There are no products in the cart!
Continue Shopping