Datron Carbide Cutting Tools

Downloads

The large chip room in this single flute allows for better chip evacuation and faster feed rates.

Single Flute End Mill

Superior chip evacuation for high-volume material removal.

The specialty-ground geometry of the single flute end mill is designed for high speed machining and high volume material removal. The large chip room in this single flute results in better chip evacuation which allows for higher feed rates and shorter cycle times. These tools are available with various cutting lengths and shank diameters. Check out all of these variants of the single flute end mill with a wide range of benefits:

Polished Single Flute End Mill
Balanced Single Flute End Mill
4-in-1 (Wiper Flat) Single Flute End Mill

 

Info

Monoblock for face milling, roughing, finishing and contouring.

Monoblock Cutting Tool

For efficient face milling and so much more!

The DATRON HSK-E 25-based Monoblock Tool is more than just an amazing face milling tool. The monoblock gives you the flexibility to do face milling, roughing, finishing and contouring. Plus, replaceable carbide cutting inserts are available for a variety of materials.

Info

The large-format MLCube has a 60" x 40" machining area that is ideal for milling sheet material.

Acrylic Cutting Tools

Cost-effective acrylic processing with glass-like surface finishes.

Until now, there was no alternative to expensive natural or industrial diamond-coated polishing end mills for glossy machining of transparent plastics such as acrylics or plexiglass. DATRON now offers Acrylic Cutting Tools -- a cost effective alternative to diamond-tipped polishing end mills. With the new series of polished milling tools, DATRON helps you to achieve highly transparent milling results at a remarkably low cost.

Info

DATRON foam cutting tools for efficient processing of PU foam.

Foam Cutting Tools

An alternative to wire, waterjet and laser processing of PU Foam.

The perfect alternative to conventional PU foam machining. DATRON foam mills offer a cost-effective, time-saving and, most-importantly, a rework-free alternative to conventional machining methods such as wire, water jet and laser cutting of polyurethane foams. The new DATRON foam mill series with the specially developed DATRON shank mills and countersinks models achieve uniquely precise results when milling PU foams.

Info

Two-flute end mill with a flat bottom made of solid carbide for durability.

Double Flute End Mill

Available in many variations for a wide range of applications.

DATRON double flute end mills are available in special variations - with extra short cutting edge, toric cut, stepped and coated micro-tools with extra short flutes for steel machining..

Info

DATRON multi flute end mills are available with different specialty coatings that improve efficiency and durability.

Multi Flute End Mills

3-, 4-, 6-, 8- & 12-flutes.

Whether with three, four, six, eight or twelve cutting edges – all DATRON multi-flute tools are developed for steel machining, have a stable cutting geometry and heavy-duty coatings.

Info

Micro toothed end mills are designed for milling abrasive materials like glass-filled plastic.

Micro Toothed End Mills

For abrasive materials like composites or engineered plastics.

Abrasive materials, such as CRP, GRP or printed circuit board material can be reliably machined at low cost with the micro-toothed end mills from DATRON..

Info

DATRON drills and thread mills made of solid micro grain carbide

Drills and Thread Mills

We even have a combination tool that drills a hole and threads it too!

DATRON tools deliver eliable drilling from a diameter of 0.1 mm and thread milling in a flash from M1.0. Our innovative thread mill performs core hole drilling and thread milling with only one tool ... in a single work step.

Info

Get exceptional radius cuts with superior edge finishes using DATRON radius end mills.

Radius End Mill

High-quality radius cuts with exceptional edge finish.

DATRON radius end mills feature extremely sharp cutting edges for exceptional results on radius cuts with no post processing required.

Info

DATRON offers a wide range of engraving tools with various shank sizes and degrees of tip sharpness.

Engraving and Counter Sink

A wide variety of shank sizes and degrees of tip angle.

Engraving, deburring and chamfering. DATRON micrograin solid carbide engraving tools are available in various shank sizes degrees of tip sharpness. Additionally, they are offered in a balanced model and for steel engraving. Plus, we even spring-mounted cutting diamond for jewelry engraving and suitable for metals.

Info

DATRON offers a wide range of engraving tools with various shank sizes and degrees of tip sharpness.

Dental Milling Tools

For Zirconium Oxide, CrCo, Titanium, Nanocomposite, PMMA or Wax.

DATRON offers the optimum milling tools for the dental materials you intend to machine. Thanks to the coatings, specially adapted to the material, the highest surface quality and long tool life are guaranteed.

For detailed information and further dental milling tools check out our special dental milling tools catalog!

 

Info

Specialty tool coatings for additional hardness and extended tool life.

Tool Coatings

Extend tool life with these specialty coatings.

The dependable characteristics of DATRON high-quality tools are further improved with by several unique material coatings. These specialty coatings provide an improved hardness enabling faster feed rates, and a smoother surface finish.  In addition, these coatings allow for optimized tool wear and increased continuous production times.

Info

ASK A QUESTION OR REQUEST A CALL BACK: